+ Installation VideosTest - Watch these GutterLock Bidding and Installation Videos. If you wish to be a GutterLock Certified Installer, answer the quiz questions. Enter your name, phone number and e-mail address at the bottom of the page and click "Submit" when you have completed watching each video and answering each quiz.

The GutterLock Elite and Extreme Flow Install Manual is also available as a PDF download. Click here (8.0 mb file).

 

Bidding a GutterLock Installation - Part 1

Bidding Questions - Part 1:

1. Should GutterLock be installed on gutters that are falling off the house? Yes       No

2. If GutterLock is installed on an already failing gutter system without being fixed, homeowners will:
 Blame the gutters failing on you
 Be ok with how everything is working
 Refer you to neighbors

3. After gutters are inspected you then move on to looking at:
 How long the roof is
 How tall the house is
 What accessories you’ll need

4. Test pieces are used for:
 Testing if the gutters are too high
 Testing if the shingles are covering the Z-bend
 Both a and b

5. If gutters are too high for Elite/Extreme flow but you don’t want to lower them then Diamond is then next alternative.
True       False
Bidding a GutterLock Installation - Part 2

Bidding Questions - Part 2:

1. Although GutterLock recommends certain snips, any metal snips will work.
True      False

2. The hand break is mainly used for:
Straightening out pieces of diamond
Breaking apart the shingles
Bending the endcaps

3. Do the gutters need to be cleaned out before our products are installed?
Yes      No

4. If shingles need to get trimmed back, besides a hook blade, the best tool to use is:
Metal snips
Putty knife
Shingle shears

5. If all the proper steps are taken and the job is done right from start to finish the first time, you won’t get any call backs.
True      False
Elite & Extreme Flow - Straight Run + End Cap

Click the "Expand Video" button (Bottom right of the preview window)
to view full screen.

Quiz 1:

1. Install the Elite/Extreme panels working from:
Left to Right   
Right to Left  
Middle

2. The Panel should be bent at the Z-Bend to what angle?
90 degree    
30 degree   
 Matching the roof pitch.

3. Slide the panel:
Under the starter shingles    
Under the first course.

4. Screw the panel to the:
 Roof along the top of the panel   
 Front gutter lip.

5. The endcap should be installed:
 Outside of the gutter  
On the inside of the gutter
GutterLock Elite & Extreme Flow - Inside Corner
+ Diverter

Click the "Expand Video" button to view full screen.

Quiz 2:

1. Install the Elite/Extreme panels working from:
Left to Right   
Right to Left  
Middle

2. Use which tool for cutting the panels:
Snips    
Hacksaw     
Hand Brake

3. You don’t need the interlocking tabs on the left side panel for the inside miter.
True    
False

4. There is a pre-made inside miter accessory used when making and inside miter.
 True   
 False

5. The diverter should be bent to:
 90 degree angle  
110 degree angle  
30 degree angle
Elite & Extreme Flow - Outside Corner
Click the "Expand Video" button to view full screen.

Quiz 3:

1. Install the Elite/Extreme panels working from:
Right to Left   
Middle   
Left to Right

2. The first measurement should start from:
The end of the last panel      
The brackets      
The end of the shingles

3. How far past the edge of the gutter do you measure for the first cut?
1/4"    
1/2"     
3/4"

4. Is the right panel screwed down before moving on to the left panel?
  No      
Yes

5. Since the ridge cap on the roof is nailed down so closely to roof line the panels need to be trimmed in order to slide under it.
 True  
False
Diamond - Straight Run + Outside Corner
Click the "Expand Video" button to view full screen.

Quiz 4:

1. Install the Diamond panels working from:
Right to Left   
Middle   
Left to Right

2. To attach the Diamond panel to the top front of the gutter, it’s recommended to use::
Two Screws    
Three Screws  
12 Screws

3. To attach the Diamond panel to the gutter or fascia, it’s recommended to use:
5 Screws    
3 Screws

4. You can use the diamond holes on the panel to help guide you in cutting a straight line instead of marking it. 
 True  
False

5. The right side panel of an outside corner requires:
 Cutting an overlapping tab  
Cutting a Z-Bend    
Nothing
Diamond - Inside Corner + Diverter
Click the "Expand Video" button to view full screen.

Quiz 5:

1. Install the Diamond panels working from:
Right to Left   
Middle   
Left to Right

2. When marking the first piece for cutting you need to measure from the front rail, not the screw tab.
True     
False

3. Trim the screw rail from the left panel:
By about 10"    
To the edge of the corner.

4. For the right side of the inside corner, cut a screw tab:
 True  
 False

5. A diverter should be added:
 On top of the Diamond Panel  
On the roof valley

After taking the entire quiz, please enter your info:

Name:

Company Name/Location:

Phone Number:

E-Mail Address: